Radio universal dimmer, 4 channels, REG - Dimmer modular distributor FM UD 420250 REG

Radio universal dimmer, 4 channels, REG - Dimmer modular distributor FM UD 420250 REG – Jung – 4011377087545: Radio universal dimmer 4-channel, REG FM UD 420250 REG combination base element with complete housing, radio operating mode, phase control dimming, phase control dimming, load type universal, light value memory, mounting type REG, mounting type other, material plastic, halogen-free, nominal voltage 230 ... 230V, frequency 50 ... 60Hz, connection type screw terminal, wire cross section 0.5 ... 4mm², device width 144mm, REG housing 8 HP new system function: fully encrypted radio transmission (AES-CCM) from eNet server software version 2.0 Intended use Switching and dimming of light bulbs, HV -Halogen lamps, electronic transformers for halogen or LED lamps, dimmable inductive transformers for halogen or LED lamps, HV LED or compact fluorescent lamps Operation with power supply 12 V REG (item no. NT 1220 REG VDC) and eNet radio -Receiver module REG (item no. FM FK 32 REG) or eNet server Operation with suitable eNet radio transmitters Mounting on top-hat rail according to DIN EN 60715 in sub-distributor Product features Switching on using lamp-friendly soft start Switch-on brightness can be permanently saved for each output Minimum brightness can be saved permanently for each output Scene operation possible Status display of the outputs via LED Status feedback to radio transmitter Outputs can be switched with the Prog button Increase in output power possible by connecting several outputs in parallel Electronic short-circuit protection with permanent switch-off after 7 seconds at the latest Electronic over-temperature protection Automatic or manual setting of the dimming principle that suits the load Power expansion through power additives (Art.- No. ULZ 1755 REG) possible Optional accessories: Compensation module LED, item no.: KM LED 230 U Adjustable with eNet server: Maximum brightness Dimming speed On/off delay Dimming up/down ramp Switch-off warning Control locks Permanent on, permanent off Hotel function Follow-up time Additional functions with eNet server: Fully encrypted radio transmission (AES-CCM) from eNet server software version 2.0 Update of the device software Read out error memory Nominal voltage: AC 230 V ~, 50/60 Hz Power loss: max. 8 W Standby power: max. 1.2 W Ambient temperature: -5 ... +45 °C connected load per output at 45 °C performance information including transformer power loss. Operate inductive transformers with at least 85% nominal load. With ohmic-inductive mixed load, max. 50% share of ohmic load. Otherwise the dimmer may be incorrectly calibrated. Load outputs connected in parallel should only be utilized up to 95%. The minimum load when connecting load outputs in parallel is 250 VA. Incandescent lamps: 20 ... 250 W HV halogen lamps: 20 ... 250 W Electronic transformers: 20 ... 250 W Electronic transformers with LV LED: typ. 20 ... 100 W Inductive transformers: 20 ... 250 VA inductive transformers with LV LED: typ. 20 ... 100 VA HV LED lamps dimmable: typ. 3 ... 50 W Compact fluorescent lamps dimmable: typ. 3 ... 50 W With the setting ''LED trailing edge'' ' the maximum connected load for HV LED lamps and electronic transformers with LV LED doubles. Ohmic-inductive: 20 ... 250 VA Ohmic-capacitive: 20 ... 250 VA Capacitive-inductive: not permitted Additional power: see instructions for additional power Connection Outputs Connection type: Screw terminals solid: 1 x 1.5 ... 4 mm2 fine-wire without Ferrule: 1 x 0.75 ... 4 mm2 fine-stranded with ferrule: 1 x 0.5 ... 2.5 mm2 Contact type: e Length of load cable per channel: max. 100 m Installation width: 144 mm (8 HP) Bus cable nominal voltage : DC 12 V SELV Current consumption: 10 mA Bus connection: Connection terminal Cable length: max. 3 m